Servo Control Archives

This article is a continuation of the series on Arduino Project – Servo Control Using Accelerometer ADXL345 and carries the discussion on how to control the motor using the sensor.

Prerequisites

To continue with this tutorial, you must have read the below articles

Embedded Sensor – ADXL345
Embedded Interface – Servo Control (Add Soon)

Components Needed:

Arduino IDE (Web or Installed on the machine)
PC
Servo Motor
ADXL345 Accelerometer Sensor
Arduino Board (e.g., Arduino Uno)
Jumper wires
Breadboard

Connection Diagram

Arduino Project Servo Control Using Accelerometer ADXL345

Wiring

Connect the VCC pin of the ADXL345 to the 3.3V pin on the Arduino.
Connect the GND pin of the ADXL345 to the GND pin on the Arduino.
Connect the SDA pin of the ADXL345 to the A4 pin on the Arduino.
Connect the SCL pin of the ADXL345 to the A5 pin on the Arduino.
Connect the signal wire of the servo motor to a digital pin on the Arduino (e.g., Pin 5).
Connect the power (VCC) and ground (GND) of the servo motor to the corresponding pins on the Arduino.

Arduino Library used List

Arduino libraries are collections of pre-written code that simplify complex tasks and allow users to easily integrate functionality into their Arduino projects. Libraries provide functions and routines that can be used to perform various tasks without the need for users to write the code from scratch. Arduino libraries are written in C or C++ and can be shared and reused by the Arduino community

Code

/* ArunEworld - @2024
Accelerometer connection pins (I2C) to Arduino are shown below:

Arduino     Accelerometer ADXL345
  A5            SCL
  A4            SDA
  3.3V          CS
  3.3V          VCC
  GND           GND
  
Arduino     Servo No. 1
  5V          5V  (Red Wire)
  GND         GND (Black Wire)
  D5          (last wire for control - might be white color)
  
Arduino     Servo No. 2
  5V          5V  (Red Wire)
  GND         GND (Black Wire)
  D6          (last wire for control - might be white color)
*/

#include <Wire.h>
#include <ADXL345.h>

#include <Servo.h>

Servo servo1;  // create servo object to control a servo
Servo servo2;

ADXL345 adxl; //variable adxl is an instance of the ADXL345 library

int x, y, z;
int rawX, rawY, rawZ;
int mappedRawX, mappedRawY;

void setup() {
  Serial.begin(9600);
  adxl.powerOn();
  servo1.attach(5);
  servo2.attach(6);
}

void loop() {
  adxl.readAccel(&x, &y, &z); //read the accelerometer values and store them in variables  x,y,z

  rawX = x - 7;
  rawY = y - 6;
  rawZ = z + 10;
  
  if (rawX < -255) rawX = -255; else if (rawX > 255) rawX = 255;
  if (rawY < -255) rawY = -255; else if (rawY > 255) rawY = 255;
   
  mappedRawX = map(rawX, -255, 255, 0, 180);
  mappedRawY = map(rawY, -255, 255, 0, 180);
  
  servo1.write(mappedRawX);
  delay(15);
  servo2.write(180 - mappedRawY);
  delay(15);
  
  Serial.print(" mappedRawX = "); Serial.print(mappedRawX); // raw data with offset
  Serial.print(" mappedRawY = "); Serial.println(mappedRawY); // raw data with offset
}

Testing

Power up your Arduino board.
Tilt the ADXL345 accelerometer in different directions to observe changes in the accelerometer data on the Serial Monitor.
The servo motor should move in response to the accelerometer data, adjusting its position based on the tilt of the accelerometer.

Troubleshooting

If the servo doesn’t move as expected, check the wiring and make sure all connections are secure.
Adjust the servo angle mapping and constraints in the code if needed.
Ensure that the accelerometer is correctly connected and functioning.

That’s it! You should now have a working setup where the servo motor is controlled based on the tilt data from the ADXL345 accelerometer. Feel free to experiment with the code and make modifications to suit your specific requirements.

Arduino-Get Start

Arduino Interface

Arduino Interface-LED

Arduino Interface-Button

Arduino Interface -Buzzer

Arduino Interface-ADC

Arduino Interface-UART(Serial)

Arduino Interface-PWM

Arduino Interface-RGB LED

Arduino Interface-LCD

Arduino Tutorials

Random Number Generator